Motor Full Load Current Calculator: Wire & Breaker

Table of Contents

Sizing a motor circuit isn’t like sizing any other load. The NEC tells you to start from table full-load current instead of the nameplate, size conductors at 125%, set overloads from the nameplate, and allow short-circuit protection well above the wire’s ampacity so the motor can start. This free motor full-load current calculator does all of that from NEC 2023 Article 430 for three-phase induction, synchronous, single-phase and DC motors. It also shows locked-rotor current, an animated starting-current profile, a current ladder and a one-line view of the circuit, plus every step.

Motor Full-Load Current & Protection Calculator

Look up motor full-load current from the NEC 2023 tables, then size the branch-circuit conductors, overloads, short-circuit and ground-fault protection, and disconnect. Includes locked-rotor current, an animated starting-current profile and a one-line view of the motor circuit.

Conductors ≥ 125% FLC (430.22)  |  Overloads ≤ 115–125% nameplate (430.32)  |  SCGF per Table 430.52(C)(1)
Try an example
Motor type:
Rotor / design:
Rated power factor:
Motor rating
Table values apply across the system voltage range shown.
Only sizes listed in the NEC table for this voltage are shown.
Selects the next listed HP at or above kW ÷ 0.746.
Nameplate (for overloads)
Overloads are based on nameplate current (430.6(A)(2)). Leave blank to use table FLC as a placeholder.
If blank, the Table 430.251 value is used where one exists.
Service factor:
Temperature rise:
Conductor conditions (Table 310.16, 310.15 and 110.14(C))
Conductor:
Insulation rating:
Terminal rating:
Table 310.15(B)(1)(1).
More than 3 applies Table 310.15(C)(1).
More than 1 set: 1/0 AWG and larger only (310.10(G)).
Starting method and FLA estimate (for the graphs)
Starting method:
Depends on the load. Used only for the illustrative profile.
Link copied. It opens this calculator with your inputs filled in.
Full-load current (table FLC)
—A
Branch-circuit conductor
—
Min. conductor ampacity
—A
Overload trip, max
—A
Inverse-time breaker, max
—A
Dual-element fuse, max
—A
Disconnect rating, min
—A
Locked-rotor current
—A
Calculated FLA (estimate)
—A
The motor circuitSupply to motor, per NEC Article 430
Starting current (illustrative)
Current ladder (log scale)
Short-circuit and ground-fault protection (Table 430.52(C)(1))
Show step-by-step solution
    Method per NFPA 70® (NEC®) 2023, Article 430 Full-load current from Tables 430.247 (DC), 430.248 (single-phase) and 430.250 (three-phase, including synchronous motors at 0.9 and 0.8 power factor) is used for conductors, short-circuit and ground-fault protection and disconnects, not the nameplate (430.6(A)(1)). Overloads use the nameplate current (430.6(A)(2), 430.32(A)(1)).
    Conductors: ampacity of at least 125% of FLC (430.22) from Table 310.16 with ambient correction (Table 310.15(B)(1)(1)) and adjustment (Table 310.15(C)(1)), not exceeding the terminal-temperature ampacity (110.14(C)). Small-conductor limits in 240.4(D) don't apply to motor circuits (240.4(G)).
    Short-circuit and ground-fault protection: percentages of FLC from Table 430.52(C)(1); when the result isn't a standard rating, the next higher standard rating is permitted (Exception No. 1). Locked-rotor current: Tables 430.251(A) and 430.251(B), intended for selecting disconnects and controllers. Disconnect ampere rating of at least 115% of FLC (430.110(A)).
    Values used per NFPA 70®, National Electrical Code® (NEC®), 2023 edition. The full code is available from NFPA, including free read-only online access. NFPA 70®, National Electrical Code® and NEC® are registered trademarks of the National Fire Protection Association. ShaiLearning is not affiliated with or endorsed by NFPA.
    Results are for educational and preliminary reference only. Always verify against applicable project standards, AHJ requirements, manufacturer data and licensed engineering judgment.
    See more resources: FE and PE Electrical Guide

    How to Use the Motor FLC Calculator

    1. Choose the motor type. Pick three-phase induction (squirrel cage, Design B energy-efficient or wound rotor), three-phase synchronous (with its rated power factor), single-phase or DC.
    2. Pick the voltage and horsepower. Only sizes listed in the NEC table for that voltage appear. Have a kW rating instead? Enter it and press Use to select the next listed horsepower.
    3. Enter nameplate data. Nameplate FLA sets the overload. Service factor and temperature rise decide between 125% and 115%. Nameplate LRA is optional.
    4. Set conductor conditions (optional): copper or aluminum, insulation and terminal ratings, ambient temperature, conductor count and parallel sets.
    5. Choose a starting method (optional) to see how across-the-line, soft-starter and VFD starts compare on the starting-current graph.
    6. Calculate. You get table FLC, the conductor size, overload and short-circuit ratings, the disconnect rating and locked-rotor current. Open Show step-by-step solution for every substitution, or use Print / Save as PDF.

    Motor Circuit Sizing Rules (NEC 2023 Article 430)

    • Full-load current: use Tables 430.247, 430.248 or 430.250, not the nameplate, for conductors, short-circuit and ground-fault protection and disconnects (430.6(A)(1)).
    • Conductors: ampacity of at least 125% of FLC (430.22).
    • Overloads: based on nameplate current, at no more than 125% for a service factor of 1.15 or more or a temperature rise of 40 °C or less, and 115% for all others (430.32(A)(1)).
    • Short-circuit and ground-fault protection: a percentage of FLC from Table 430.52(C)(1), such as 250% for an inverse-time breaker or 175% for a dual-element fuse on most AC motors. If the result isn’t a standard size, the next higher standard rating is permitted.
    • Disconnect: an ampere rating of at least 115% of FLC (430.110(A)).

    Worked Example: 50 HP, 460 V, Three-Phase Squirrel-Cage Motor

    Nameplate: 62 A, service factor 1.15. Copper conductors with 75 °C terminals.

    1. Table 430.250 FLC: 65 A.
    2. Conductors: 1.25 × 65 = 81.3 A, so 4 AWG copper (85 A at 75 °C).
    3. Overload: 1.25 × 62 A = 77.5 A maximum.
    4. Inverse-time breaker: 2.5 × 65 = 162.5 A, so the next standard size is 175 A. A dual-element fuse works out to 1.75 × 65 = 113.8 A, so 125 A.
    5. Disconnect: 1.15 × 65 = 74.8 A minimum, rated at least 50 HP.
    6. Locked-rotor current from Table 430.251(B): 363 A, about 5.6 times FLC.

    Notice the 175 A breaker on 85 A wire. That’s correct for a motor circuit: the overload protects the conductors from running overcurrent, and the breaker only needs to clear short circuits and ground faults while letting the motor start.

    FE/PE Exam and Field Tips

    • Table FLC vs. nameplate: the most common exam trap. Use the table for wire and breakers and the nameplate for overloads.
    • Match the table voltage. A 460 V motor on a 480 V system uses the 460 V column. A 230 V column covers 220–240 V systems, but 208 V motors have their own column.
    • Small wire is allowed on motor circuits. The 240.4(D) limits don’t apply (240.4(G)), so 12 AWG copper can sit behind a 45 A breaker on a motor branch circuit.
    • Design B energy-efficient motors draw more locked-rotor current, which is why Table 430.52(C)(1) allows instantaneous-trip settings up to 1100% for them.
    • Long run? Check the drop with the Voltage Drop Calculator . Motors are sensitive to low voltage during starting.
    FAQ

    Frequently Asked Questions

    Why use the NEC table FLC instead of the nameplate FLA?

    430.6(A)(1) requires the table values for sizing conductors, short-circuit and ground-fault protection and disconnects. That way the installation still works if the motor is later replaced with one that draws a different current. The nameplate is used for overload protection (430.6(A)(2)).

    How do I size motor branch-circuit conductors?

    For a single continuous-duty motor, the conductor ampacity must be at least 125% of the table FLC (430.22). Then apply ambient and bundling factors, and check the terminal temperature rating. The calculator does each of these steps and shows them.

    What size overload do I need?

    The maximum is 125% of nameplate FLA for motors marked with a service factor of 1.15 or more or a temperature rise of 40 °C or less, and 115% for all other motors (430.32(A)(1)). If the motor can't start or carry its load at that setting, 430.32(C) permits a limited increase.

    Why can the breaker be larger than the wire's ampacity?

    In a motor circuit, the overload relay protects the motor and conductors from running overcurrent. The branch-circuit breaker or fuse only needs to protect against short circuits and ground faults, so it's sized high enough to carry the starting current. Table 430.52(C)(1) sets the maximum percentages.

    What is locked-rotor current, and is it the same as inrush?

    Locked-rotor current (LRA) is the steady current a motor draws at standstill with full voltage applied, often about 5 to 8 times FLC for induction motors. Inrush usually refers to the very first cycles, which can briefly exceed LRA because of DC offset. Tables 430.251(A) and (B) give maximum locked-rotor values for selecting disconnects and controllers.

    How do soft starters and VFDs change the picture?

    A soft starter limits starting current, typically to a few times FLC, at the cost of lower starting torque. A VFD accelerates the motor at roughly rated current. Both reduce voltage dip and mechanical stress. The starting graph in the calculator is illustrative, so use manufacturer data for real coordination.

    Does the calculator handle synchronous and DC motors?

    Yes. Synchronous motor FLC comes from Table 430.250 and is multiplied by 1.1 at 0.9 power factor or 1.25 at 0.8 power factor. DC motors use Table 430.247 and the DC row of Table 430.52(C)(1).

    What about motors over 1000 V?

    The calculator shows full-load current for 2300 V motors. Conductors and protection over 1000 V fall under Part XI of Article 430 and use different rules, so those results aren't shown.

    Related Calculators

    Preparing for the FE or PE Electrical Exam?

    Get structured guidance from a licensed P.E. through the ShaiLearning FE & PE mentorship program. Join the waitlist, and explore the FE Electrical Guide and PE Power Guide.

    Values used per NFPA 70®, National Electrical Code® (NEC®), 2023 edition. The full code is available from NFPA, including free read-only online access. NFPA 70®, National Electrical Code® and NEC® are registered trademarks of the National Fire Protection Association. ShaiLearning is not affiliated with or endorsed by NFPA.

    Results are for educational and preliminary reference only. Always verify against applicable project standards, AHJ requirements, and licensed engineering judgment.

    Leave a Reply

    Your email address will not be published. Required fields are marked *

    Related posts you might like

    Impedance Calculator

    This impedance calculator finds Z in rectangular and polar form from R and X, from |Z| and angle, from series

    Read More »

    Ohm’s Law Calculator

    The Ohm’s law calculator solves for voltage, current, resistance, and power from any two known values. Ohm’s law is the

    Read More »

    Why Large Power is Transmitted at High-Voltage

    Electricity is rarely made where it is used. A high voltage transmission system makes it possible to reach all demand

    Read More »