Ohm’s Law Calculator

Table of Contents

This free Ohm’s law calculator solves for voltage, current, resistance, and power from any two values you know. Ohm’s law is the first equation every electrical engineer learns, and it’s also the one they use most. Besides the answer, you see current flow on an animated circuit, the formula used on the Ohm’s law wheel, and the operating point on a V-I chart. It also calculates heat output, energy use, and cost, and shows every step of the math.

Ohm's Law & Power Calculator

Enter any two of voltage, current, resistance and power to solve the other two. Watch current flow through an animated circuit, see the formula used on the Ohm's law wheel, and get heat, energy and cost at a glance.

V = I · R  |  P = V · I = I² · R = V² / R
Try an example
I know:
Known values
Works for DC circuits and for resistive AC loads using RMS values. For motors and other loads with reactance, use the Impedance Calculator.
Energy and cost (optional)
Use your utility's energy rate. Demand and fixed charges aren't included.
Link copied. It opens this calculator with your inputs filled in.
Results
—
Voltage V
—
Current I
—
Resistance R
—
Power P
—
Conductance G = 1/R
—
Heat output
—BTU/h
Energy
—
Energy cost
—
Resistor wattage
—
The circuitCharge speed follows current, glow follows power
Ohm's law wheel
V-I chart
Show step-by-step solution
    Formulas Ohm's law: V = I · R, I = V / R, R = V / I. Power: P = V · I = I² · R = V² / R. From power: I = P / V, R = V² / P, V = P / I, R = P / I², V = √(P · R), I = √(P / R). Conductance G = 1 / R (siemens). Heat: 1 W = 3.412 BTU/h. Energy: kWh = P (kW) × hours.
    For AC circuits these hold for purely resistive loads with RMS voltage and current. With reactance, use impedance Z and power factor instead.
    NFPA 70®, National Electrical Code® and NEC® are registered trademarks of the National Fire Protection Association. ShaiLearning is not affiliated with or endorsed by NFPA.
    Results are for educational and preliminary reference only. Always verify against applicable project standards, AHJ requirements, and licensed engineering judgment.
    See more resources: FE and PE Electrical Guide

    How to Use the Ohm's Law Calculator

    1. First, choose the two values you know: V & I, V & R, I & R, P & V, P & I, or P & R.
    2. Next, enter them with their units. You can switch between mV, V and kV; mA, A and kA; mΩ through MΩ; and mW through MW. When you change a unit, the value converts automatically.
    3. Then add energy details (optional). For example, enter hours per day, days per year and your electricity rate to see kWh and cost.
    4. Finally, click Calculate. As a result, you get all four quantities in the most readable units, as well as conductance, heat in BTU/h and a suggested resistor wattage for small loads. Afterward, open Show step-by-step solution or use Print / Save as PDF.

    Ohm's Law and Power Formulas

    Ohm's law states that V = I × R. In other words, the voltage across a resistor equals the current through it times its resistance. Because power is P = V × I, you can combine the two equations and solve for any quantity from any other two.

    • Voltage: V = I × R = P ÷ I = √(P × R)
    • Current: I = V ÷ R = P ÷ V = √(P ÷ R)
    • Resistance: R = V ÷ I = V² ÷ P = P ÷ I²
    • Power: P = V × I = I² × R = V² ÷ R
    • Heat: 1 W = 3.412 BTU/h. Energy: kWh = kW × hours.

    In short, these twelve formulas make up the Ohm's law wheel. They apply to DC circuits, and also to purely resistive AC loads when you use RMS values. However, when a load has inductance or capacitance, use impedance instead of resistance. Also, for the SI definitions of the volt and the ohm (1 Ω = 1 V/A), see the NIST SI units page for electric current.

    Ohm's Law Calculator Examples

    Example 1: 1,500 W heater on 120 V

    Ohm's law calculator results for a 1,500 W heater on 120 V: 12.5 A and 9.6 Ω on the Ohm's law wheel and V-I chart
    The Ohm's law calculator solving the 1,500 W heater example.

    First, find the current: I = P ÷ V = 1,500 ÷ 120 = 12.5 A. Next, find the resistance: R = V² ÷ P = 120² ÷ 1,500 = 9.6 Ω. The heater therefore gives off 1,500 × 3.412 ≈ 5,118 BTU/h. If it runs 4 hours a day at $0.15/kWh, it uses 6 kWh/day, so it costs about $328.50 a year.

    Also, because it runs for 3 hours or more, it counts as a continuous load. As a result, the circuit is sized at 12.5 × 1.25 = 15.6 A, so it needs a 20 A circuit rather than a 15 A one. In addition, you can read the continuous-load rules in the NEC free of charge from the NFPA 70 page after creating an NFPA account.

    Example 2: 9 V across a 470 Ω resistor

    In this case, I = 9 ÷ 470 = 19.15 mA, and P = 9² ÷ 470 = 172 mW. Then, doubling that for margin gives 345 mW, so a ½ W resistor is the right choice.

    Ohm's Law Tips for the FE/PE Exam and the Field

    • Pick the formula that uses what you know. For example, if you have P and R, go straight to I = √(P ÷ R) instead of solving in two steps.
    • Power goes with the square. So doubling the current through a resistor quadruples its heat. That's also why loose connections run hot.
    • Watch the units. For instance, mA × kΩ gives volts directly, which makes it a handy shortcut for electronics problems.
    • AC loads with reactance need impedance and power factor, so for those, use the Impedance Calculator or the kW to Amps Calculator .
    FAQ

    Frequently Asked Questions

    What can this Ohm's law calculator solve?

    It solves voltage, current, resistance and power from any two of them. In addition, it gives conductance, heat in BTU/h, daily and yearly energy, energy cost and a suggested resistor wattage. It also shows every step, so you can check the math by hand.

    What is Ohm's law?

    Ohm's law says that the current through a resistor is proportional to the voltage across it, so V = I × R. Here, voltage is in volts, current in amperes and resistance in ohms.

    How do I calculate power from voltage and current?

    Multiply them: P = V × I. Also, you can use P = I² × R when you know current and resistance, or P = V² ÷ R when you know voltage and resistance.

    How many amps does a 1,500 W heater draw on 120 V?

    I = P ÷ V = 1,500 ÷ 120 = 12.5 A. However, if the heater runs for 3 hours or more, it is a continuous load, so the circuit is sized for 125% of that, or 15.6 A. As a result, it needs a 20 A circuit.

    Does Ohm's law work for AC circuits?

    Yes, for purely resistive loads such as heaters and incandescent lamps, as long as you use RMS voltage and current. However, for motors, transformers and other loads with inductance or capacitance, replace R with impedance Z and include the power factor.

    What is conductance?

    Conductance is the reciprocal of resistance, G = 1 ÷ R, measured in siemens (S). It's useful when you add parallel branches, because parallel conductances simply add.

    How do I choose a resistor wattage?

    First, calculate the power the resistor dissipates, and then pick a rating of at least about twice that. This margin keeps it cooler and therefore more reliable. Also, check the manufacturer's derating curve when it will run in a hot enclosure.

    How do I convert watts to BTU per hour?

    Multiply by 3.412. For example, a 1,500 W heater produces about 5,118 BTU/h.

    Related Calculators

    Next, try these related tools, since each one builds on Ohm’s law for AC circuits and wiring.

    Preparing for the FE or PE Electrical Exam?

    Get structured guidance from a licensed P.E. through the ShaiLearning FE & PE mentorship program. Join the waitlist, and explore the FE Electrical Guide and PE Power Guide.

    NFPA 70®, National Electrical Code® and NEC® are registered trademarks of the National Fire Protection Association. ShaiLearning is not affiliated with or endorsed by NFPA.

    Results are for educational and preliminary reference only. Always verify against applicable project standards, AHJ requirements, and licensed engineering judgment.

    Leave a Reply

    Your email address will not be published. Required fields are marked *

    Related posts you might like

    Why Large Power is Transmitted at High-Voltage

    Electricity is rarely made where it is used. A high voltage transmission system makes it possible to reach all demand

    Read More »

    What are the 9 Knowledge Areas of the PE Exam and the Blueprint to Pass it

    The PE Power exam blueprint maps every topic NCEES tests on the PE Electrical and Computer: Power exam. If you

    Read More »

    FE Electrical & Computer Exam Overview: The 17 Knowledge Areas Explained

    FE Electrical & Computer Exam Overview: The 17 Knowledge Areas Explained — ShaiLearning Today, let’s talk about the FE Electrical

    Read More »