This transformer sizing calculator recommends a standard transformer rating from your plant output or load list. Picking a transformer rating takes more than dividing kW by power factor, because you also have to account for the reactive power the grid requires, the lowest voltage the transformer will run at, how much cooling the fans add, altitude, and how the code limits the protection around it.
In particular, the calculator handles two jobs: it sizes a main power transformer from a plant’s real power and power factor requirement at the point of interconnection (POI), or it sizes a distribution transformer from a list of loads. It then recommends a standard rating with ONAN/ONAF cooling stages, shows rated and fault currents, and finally applies the NEC 450.3 overcurrent protection limits, with animated graphs and every step of the math.
Transformer Sizing Calculator
Size a power or distribution transformer from your point-of-interconnection requirements or from a list of loads. Get the recommended kVA or MVA rating with ONAN/ONAF cooling stages, altitude derating, two- or three-winding splits, rated and fault currents, and NEC 450.3 overcurrent protection limits.
Ratings per IEEE C57.12.00 Table 2 | Protection per NEC Table 450.3(A) and 450.3(B)Cooling ratios, altitude factors and impedance details
NEC 450.3 overcurrent protection settings
Show step-by-step solution
POI mode sizes on transformer current: S = √((PPOI(1 + losses))² + Q²) at the worst required power factor, divided by the minimum operating voltage in per unit. The transformer's own reactive loss (I²X) doesn't increase its current. It's reported as reactive power the plant must supply at the LV bus. Load mode adds load vectors (ΣP, ΣQ), then applies demand factor, growth margin and minimum voltage.
Overcurrent protection: maximum ratings as a percentage of transformer rated current from NFPA 70 (NEC) 2023 Table 450.3(A) (over 1000 V) and Table 450.3(B) (1000 V and less), with standard ratings from 240.6(A).
Values used per NFPA 70®, National Electrical Code® (NEC®), 2023 edition. The full code is available from NFPA, including free read-only online access. NFPA 70®, National Electrical Code® and NEC® are registered trademarks of the National Fire Protection Association. ShaiLearning is not affiliated with or endorsed by NFPA.
Standard ratings referenced from IEEE Std C57.12.00. IEEE is a registered trademark of the Institute of Electrical and Electronics Engineers, Inc. ShaiLearning is not affiliated with or endorsed by IEEE. IEEE standards are available from IEEE.
Results are for educational and preliminary reference only. Always verify against applicable project standards, interconnection requirements, AHJ requirements, manufacturer data and licensed engineering judgment.
How to Use the Transformer Sizing Calculator
- First, choose how to size. Plant output at the POI is for generation step-up (main power) transformers. In contrast, A list of loads is for facility and distribution transformers.
- POI mode: next, enter the real power and required power factor at the POI, whether the plant must deliver lagging, leading or both, and any gen-tie losses. Then pick two-winding, or three-winding with a split LV and an optional tertiary load.
- Load mode: instead, add each load in kW, kVA or HP with its quantity and power factor. Afterward, set the demand factor, growth margin and K-factor, and choose single- or three-phase, liquid-immersed or dry-type.
- Describe the transformer: for example, its cooling stages (ONAN, ONAN/ONAF or ONAN/ONAF1/ONAF2), winding voltages, %Z, the minimum and maximum operating voltage, site altitude and average ambient.
- Check the advanced settings (optional): also review fan-stage ratios, altitude derating factors, X/R ratio, and NEC 450.3 options such as supervised location and primary-only protection.
- Finally, size it. As a result, you get the recommended rating, loading at each cooling stage, rated and through-fault currents, voltage regulation, the plant reactive requirement at the LV bus (POI mode), the K-rating (load mode) and the maximum protective device ratings. Afterward, open Show step-by-step solution or use Print / Save as PDF.
How the Transformer Sizing Calculator Works
- Apparent power: S = √(P² + Q²). Specifically, in POI mode, Q = P × tan(arccos pf) at the required power factor. In contrast, in load mode, loads are added as vectors (ΣP and ΣQ), then demand factor and growth are applied.
- Minimum voltage: a transformer's thermal limit is current. For example, at 0.95 pu, the same MVA draws 5% more current, so the requirement becomes S / Vmin.
- Altitude: above 1000 m, thinner air cools less, so the ratings are derated by a percentage per 100 m.
- Standard rating: the smallest preferred rating from IEEE C57.12.00 Table 2 that covers the requirement. With fans, however, the top (forced-air) rating is chosen and the self-cooled rating follows from the stage ratios, typically 100/133/167%.
- Currents: I = S / (√3 × V) for three-phase. Similarly, LV through-fault current ≈ Irated / Z (on the self-cooled base, infinite source).
- Protection: maximum ratings as a percentage of rated current from NEC Table 450.3(A) (over 1000 V) or Table 450.3(B) (1000 V and less).
Transformer Sizing Example: 80 MW Solar Plant at a 230 kV POI
In this case, the interconnection requires 80 MW with a power factor of ±0.95 at the POI. Also, the minimum operating voltage is 0.95 pu, and %Z is 9% on the ONAN base.
- First, Q = 80 × tan(arccos 0.95) = 26.3 MVAr, so S = √(80² + 26.3²) = 84.2 MVA.
- Next, at 0.95 pu voltage: 84.2 / 0.95 = 88.6 MVA of current capability needed.
- Then the smallest Table 2 top rating that covers it is 100 MVA, so the transformer is 60/80/100 MVA ONAN/ONAF1/ONAF2, loaded to 88.6% at ONAF2.
- As a result, rated currents at 100 MVA are 251 A at 230 kV and 1,673 A at 34.5 kV. Also, the LV through-fault current is 1,004 A / 0.09 ≈ 11.2 kA.
- Finally, the transformer itself absorbs about 11.8 MVAr at this loading, so the plant must supply about +38.1 MVAr at the 34.5 kV bus to deliver the lagging requirement at the POI.
That last point is easy to miss, though. The transformer's I²X loss doesn't increase its current, so it doesn't change the rating, but it does change how much reactive capability the inverters need.
Transformer Sizing Example: Facility Loads, 13.8 kV to 480 V
In this case, five load groups add to 1,085 kW and 569 kVAr, or 1,225 kVA as a vector sum (1,233 kVA if you add kVA directly). With an 80% demand factor and 25% growth, the design load is 1,225 kVA, so the next Table 2 rating is 1,500 kVA (1,125 kVA ONAN / 1,500 kVA ONAF). Then, with 5.75% impedance, the LV through-fault current is about 23.5 kA. Under Table 450.3(A), the 480 V secondary protection is 125% × 1,804 A = 2,255 A, so the next standard size is 2,500 A.
Transformer Sizing Tips for the FE/PE Exam and the Field
- Size on current, not just MVA. So if the transformer must deliver full output at low voltage, divide by the per-unit voltage.
- Know which rating you are quoting. For example, "60/80/100 MVA" means 60 MVA self-cooled, 80 MVA with one fan stage and 100 MVA with both.
- Watch the impedance base. In general, %Z is stated on the self-cooled (ONAN) rating, so fault current and regulation use that base.
- Table 450.3(A) impedance limits. The percentages change at 6% and 10% impedance, while supervised locations allow different arrangements.
- Nonlinear loads: specify a K-rated dry-type transformer (K-4, K-9, K-13 and so on), or derate per IEEE C57.110.
- Related checks: also convert loads with the kW to Amps Calculator , solve power factor with the Power Triangle Calculator , and size feeders with the Voltage Drop Calculator .
Frequently Asked Questions
What can this transformer sizing calculator do?
It sizes a main power transformer from a plant's POI requirement, or a distribution transformer from a list of loads. In addition, it picks a standard rating with cooling stages, works out rated and fault currents, and then applies the NEC 450.3 protection limits.
How do I size a transformer for a solar or battery plant?
First, start from the real power and power factor the interconnection requires at the POI. Next, find the apparent power at the worst power factor, divide by the minimum operating voltage in per unit, and apply any altitude derating. Then pick the smallest standard rating, usually the top forced-air rating, that covers it. Finally, add any losses between the transformer and the POI.
What do ONAN, ONAF1 and ONAF2 mean?
In short, they are cooling classes for liquid-immersed transformers. Specifically, ONAN means oil natural, air natural (no fans). In contrast, ONAF means oil natural, air forced, with fans running. Two fan stages give two higher ratings, commonly about 133% and 167% of the ONAN rating. For example, a 60/80/100 MVA transformer has three ratings.
Why does minimum operating voltage affect the transformer size?
A transformer's heating depends on current, so to deliver the same MVA at 0.95 pu voltage, it carries 1/0.95 ≈ 1.053 times the current, so it needs about 5% more capability.
Does the transformer's own reactive loss increase the required rating?
No. The I²X loss raises the voltage on the source side, but the current through both windings stays the same in per unit, so the thermal requirement doesn't change. However, it does mean the plant must supply extra vars at the LV bus, which matters for inverter or reactive-device sizing.
Where do the standard kVA ratings come from?
Specifically, the calculator uses the preferred continuous kVA ratings in IEEE Std C57.12.00, Table 2, for single-phase and three-phase transformers. Above 100 MVA, it rounds up in 10 MVA steps, since ratings that large are usually specified for the project.
How does altitude affect transformer rating?
Above 1000 m (3300 ft), thinner air removes less heat, so the transformer must be derated by a percentage per 100 m. Also, the rate depends on the cooling class. The calculator therefore lets you enter the factors, so confirm them against the standard and the manufacturer.
What does NEC Table 450.3(A) require for transformers over 1000 V?
In short, it sets the maximum rating of the primary and secondary circuit breakers or fuses as a percentage of transformer rated current. Also, the limits depend on impedance (6% or less, or over 6% to 10%), the device type and whether the location is supervised. However, where a value doesn't match a standard size, the next higher standard or commercially available rating is generally permitted (Note 1).
What about transformers 1000 V and less?
Table 450.3(B) applies. When only the primary is protected, the primary device is limited to 125% of rated current (167% under 9 A, 300% under 2 A). In contrast, with primary and secondary protection, the primary may go to 250% and the secondary is limited to 125% (167% under 9 A).
When do I need a K-rated transformer?
You need one when the load includes significant nonlinear equipment, such as computers, LED drivers or variable-frequency drives, that creates harmonic currents and extra heating. Then pick a K-rating at or above the calculated K-factor of the load, or derate a standard transformer per IEEE C57.110.
Related Calculators
Next, try these related tools, since each one builds on the same ideas.
- Power Triangle Calculator
- kW to Amps Calculator
- Three-Phase & Single-Phase Power Calculator
- Voltage Drop & Wire Size Calculator
- Power Factor Correction Calculator
- Browse all Electrical Power Calculators
Preparing for the FE or PE Electrical Exam?
Get structured guidance from a licensed P.E. through the ShaiLearning FE & PE mentorship program. Join the waitlist, and explore the FE Electrical Guide and PE Power Guide.
Standard ratings referenced from IEEE Std C57.12.00. IEEE is a registered trademark of the Institute of Electrical and Electronics Engineers, Inc. ShaiLearning is not affiliated with or endorsed by IEEE. IEEE standards are available from IEEE.
Values used per NFPA 70®, National Electrical Code® (NEC®), 2023 edition. The full code is available from NFPA, including free read-only online access. NFPA 70®, National Electrical Code® and NEC® are registered trademarks of the National Fire Protection Association. ShaiLearning is not affiliated with or endorsed by NFPA.
Results are for educational and preliminary reference only. Always verify against applicable project standards, AHJ requirements, and licensed engineering judgment.


